Views:

Codes - The Basics

• The KL1500 has four code levels available:
i) Master Code
ii) Sub-Master Code
iii) User Code
iv) Technician Code

• The KL1500 is supplied with two factory set codes:
Master Code: 11 22 33 44
User Code: 12 34

• Before fitting, change the Master Code and User Code.

• All Master Codes and Sub-Master Codes are 8 digits long.

• All User Codes are 4 digits long.

• Up to 20 individual User Codes can be entered into the lock at the same time. Each User Code is entered together with specific ID (Identification Number) from 01-20.

• All Technician Codes are 6 digits long.

• The lock ‘open’ time is set at 4 seconds.

 

Functions

Before programming, select the most appropriate function for the application.

A) Private Use
Important Note: This is the default function pre-programmed in new locks.
This is the most common function and is used where the same code will be repeatedly used.

B) Public Use
The user enters their own personal code twice, the second time to confirm the correct code. This locks the lock. To open the same code is entered once again and then will be erased. The lock will remain open until a new code is entered. This function is used for short term, multi occupancy applications eg: a locker in a leisure centre or Spa.

 

Operating Instructions

The KL1500 has a 12 button keypad. The # button is used as a prefix when programming for all code levels. The KL1500 standard unit is installed in the vertical (up) position with the lever at the bottom. However, the lock may be installed in any of 4 positions; up, down, horizontal (left or right). Should the lock need to be changed from one position to another please see Installation Instructions.

 

Programming Codes

The programming functions of the code levels are:

Master Code
The Master Code can:
• Open the lock.
• Change the Master Code.
• Set Public Use or Private Use Function.
• Set, change or delete the Sub-Master Code.
• Set, change, suspend or restore User Codes.
• Set or delete Technician Code.
• Set or cancel Dual Code mode.
• Set or cancel hours locked time.
• Set 24hr clock.
• Set or cancel Auto-Open Time.
• Set lock status indicator.
• Disable or enable sounder.

 

Sub-Master Code
The Sub-Master Code can:
• Open the lock.
• Change the Sub-Master Code.
• Set, change, suspend or restore User Codes.
• Set lock status indicator.
• Disable or enable sounder.

 

User Code
The User Code can:
• Open the lock.
• Change the User Code.

 

Technican Code

The Technician Code can:
• Open the lock in Public Use Function without erasing the User Code.

The same code can be used in one level only.

 

Lost Master Code Procedure
• Remove BOTH coin cell batteries.
• Press and hold the 0 button.
• Replace one battery, Blue LED will flash twice.
• Release the 0 button and within three seconds press the 0 button 3 times.
• Blue LED will flash twice and the lock will revert back to last active mode – Public Use or Private Use 
Function and the Master Code will now be the factory default e.g. 11223344.
Note: All previously programmed codes and settings will be RETAINED.
• Replace second battery.

 

Factory Code Reset


Reset lock to factory supplied settings:
• Remove both batteries.
• Press and hold the 1 button and replace one battery.
• The blue LED will flash twice and beep twice.
• Release the 1 button and within 3 seconds press the button 3 times.
• The blue LED will flash and beep twice to confirm factory reset.
• Refit second battery.
Note: Lock will revert to Master Code of 11223344 and User Code 1234.
All previously entered settings and codes will have been ERASED.

 

Penalty TIme
• Entering three incorrect codes will cause the lock to shut down for 10 seconds.

 

Battery Power
• The KL1500 should provide in excess of 50,000 openings of 4 seconds each from 2 x CR2450 3.0 V coin cell batteries.

 

Low Battery

• When battery power is low the Red LED will flash 3 times before the Blue LED light accepting the code. Fit new batteries as soon as this happens.
Note: To retain Program 15 Time Setting, one battery must be changed at a time.

 

Battery Override
Should the batteries fail the lock can be opened using the code and an external PP3 battery as the power source as follows:

The procedure is as follows:

• Place the +positive contact of the battery against the contact point surrounding the Red LED and the –negative contact point of the battery against the contact point of the Blue LED.

• Enter Master Code.

• Lock will open.

• Remove the lock and replace batteries.

• Refit lock.

 

Master Code Commands

Set the Technican Code (Public Use Only Function)
#Master Code  10  Technician Code  Technician Code ••
Example: #11223344  10  555555  555555 ••
Result: Technician Code 555555 now valid.
Note:
• The Technician Code will open lock without erasing the Public Use Code.
• Opening the lock with the Master Code or Sub-Master Code will erase the Public Use Code.

 

Delete the Technican Code (Public Use Only Function)
#Master Code  11  11 ••
Example: 11223344  11  11 ••
Result: Technician Code deleted.

 

Set Dual Code Mode (Private Use Only Function)
#Master Code  12  12 ••
Example: #11223344  12 • 12 ••
Result: TWO valid codes required to open the lock or the Master Code only. They can be any combination of the following codes:
User Code + User Code
User Code + Sub-Master Code.

 

Cancel Dual Code Mode (Private Use Only Function)
#Master Code  13  13 ••
Example: #11223344  13  13 ••
Result: Lock will revert to only requiring one single code to open the lock.
Note: When switching between Program 12 and 13, codes and selected programs are retained.

 

Master Code Commands

Restrict the Locked Time (Public Use Only Function)
#Master Code  14  (number of hours lock to remain locked) ••
Example 1: #11223344  14  04 ••
Result:
       • After 4 hours from the time it was locked, the Public Use Code will be erased. A Master or Sub-Master Code now required to open the lock.
       • Once opened with the Master or Sub-Master Code the lock will then revert to B) Public Use with the lock open waiting for a new single Public Use Code to be entered.
       • If the lock is opened during the set 4 hour period with a User or Master Code then the lock will remain unlocked. At this point the restricted lock time expires until a New User Code is entered.
Note:
       • Program 16 (Auto-Open Time) will have priority if programmed.
       • The available restricted locked time periods in hours are: 00, 02, 04, 06, 08, 10 or 12.
       • To end restricted locked time use following program:
                        #Master Code  14  00 ••
                        Example: #11223344  14  00 ••
                        Result: Locked time will not be restricted i.e. will remain locked until User, Master or Sub-Master Code entered or Auto-Open Time, Program 16 is activated.

 

Set 24 Hour Clock to Run (Public Use Only Function)
#Master Code  15  07  30 ••
Example: #11223344  15  07  30 ••
Result: Lock internal timer has been set to 07.30hrs and will start to run.
Note: Time must be reset for daylight saving when required.

 

Master Code Commands

Set Auto Open Time (Public Use Only Function)
#Master Code  16  hour  min ••
Example: #11223344  16  19  15 ••
Result: Lock will auto-open every day at 19.15 hrs and remain unlocked until a new code is entered.
Note: 24 hr clock must be set before program will operate.

 

Cancel Auto Open Time  (Public Use Only Function)
#Master Code  17 • 17 ••
Example: #11223344  17  17 ••
Result: Auto-Open Time is cancelled.

 

Disable/Enable Sounder
The default is for the sounder to activate at every button press. To disable the sounder enter the following command:
#Master Code • 18 • 18 ••
Example: #11223344  18  18 ••
Result: No sound when buttons pressed.
To enable the sounder, repeat above code sequence.

 

Red LED Locked Status (Public Use Only Function)
Note: The factory default is for the Red LED to flash when locked every 3 seconds in B) Public Use.
#Master Code  19  19 ••
Example: #11223344  19  19 ••
Result: When locked in B) Public Use – No Red LED flashing.
To enable the Red LED to flash in B) Public Use, repeat above code sequence.

 

 

Sub-Master Code Commands

Change the User Code (Private Use Only Function)
#Sub-Master Code  03  User Code ID  User Code ••
Example: #55667788  03  003 • 1355 ••
Result: New User Code 1355 now valid in position 03.

 

Suspend Individual User Code (Private Use Only Function)
#Sub-Master Code  04  User Code ID ••
Example: #55667788  04  01 ••
Result: User Code ID number 01 valid but suspended. This will be identified by the Red and Blue LED signalling together after the code has been entered. Lock will remain locked.

 

Restore Individual User Code (Private Use Only Function)

#Sub-Master Code  05  User Code ID ••
Example: #55667788  05  01 ••
Result: User Code ID number 01 restored.

 

Suspend all User Codes (Private Use Only Function)
#Sub-Master Code  06 ••
Example: #55667788  06 ••
Result: All User Codes suspended. Red and Blue LED will signal together after every valid code is entered and lock will remain locked.

 

Restore all User Codes (Private Use Only Function)
#Sub-Master Code  07 ••
Example: #55667788  07 ••
Result: All User Codes restored.

 

Set or Change the Sub-Master Code
#Sub-Master Code  08  Sub-Master Code  Sub-Master Code ••
Example: #55667788  08  22446688  22446688 ••
Result:Sub-Master Code 22446688 now valid.

 

Sub-Master Code Commands

Disable/Enable Sounder
The default is for the sounder to activate at every button press. To disable the sounder enter the following command:
#Sub-Master Code  18 • 18 ••
Example: #55667788  18  18 ••
Result: No sound when buttons pressed.
To enable the sounder, repeat above code sequence.

 

Red LED Locked Status (Public Use Only Function)
Note: The factory default is for the Red LED to flash when locked every 3 seconds in B) Public Use.
#Sub-Master Code  19  19 ••
Example: #55667788  19  19 ••
Result: When locked in B) Public Use – No Red LED flashing.
To enable the Red LED to flash in B) Public Use, repeat above code sequence.

 

 

User Codes

User Code Commands
A User Code can change a User Code:
#User Code  New User Code ••
Example: #1234  0000 ••
Result: User Code has been changed from 1234 to 0000.

 

Technican Codes

A Technician Code can open the lock when in B) Public Use WITHOUT deleting the User Code sequence:
Enter 6 digit Technician Code, lock opens for 3 seconds and then relocks.

 

POI-KL1500-v3:0613

 

© 2018 Codelocks Ltd.  All rights reserved.