Views:

      

Note: This product will be launched Summer 2019 in North America.


Introduction

The WiFi Gateway is a wireless device used to connect compatible Codelocks smart locks to your WiFi network in conjunction with the K3 Connect app.  It can be used to manage and control locks remotely via the K3 Connect app without requiring a Bluetooth connection.




 


















Requirements

· A smart device running either Android version 4.3+ or an iPhone 4S or above running iOS 8.0+

· A compatible Codelocks smart lock

· IEEE 802.11 b/g/n (2.4GHz) wireless network

· WiFi SSID and password

· A strong and steady internet connection

· USB type A socket with a steady 5v power supply

 

Technical Specification

· One Gateway can support a maximum of 8 locks simultaneously.
· Max Distance from Gateway to Locks: 5 metres
· Operation Temperature : -20°C to 70°C (excluding plastic)
· Storage Temperature : -30°C to 80°C (excluding plastic)
· Radio Frequency: 2.4 GHz
· Power Source: USB Type A connector

Features

Using the WiFi connection the gateway has the ability remotely to complete the following:
· Unlocking locks
· Set lock parameters and access restriction
· Client management—Phone, card and code
· Generate NetCodes
· Retrieve the lock’s audit
· Receive lock event notifications
· Check the lock’s current status
 

Installation

To install the WiFi gateway simply plug it into a steady power source (ie a wall socket with USB port) which has a minimum 2.4v power supply.

Important notes:

· Do not place the gateway within any type of container including boxes, cabinets and walls as this will block the device’s WiFi connection.

· Install the gateway more than 1 meter from your router.  If both devices are close to each other this may cause interference.

· The gateway should be installed no more than 5 meters from the locks, any more than this will likely cause a poor connection.

· The best connection can be obtained by installing both the lock and gateway in the same space with minimal walls, rooms etc between the two which could cause line-of-sight issues.

· Even though one gateway has the ability to control multiple locks we recommended using multiple gateways to guarantee a better range and service.

Operation Instructions

Before proceeding:  If you have not done so already, download the K3 Connect app and add the locks.  For more detailed instruction on how to do this check your lock’s programming and operation instructions or the K3 Connect user guide.

Note: You must be the lock’s administrator to add it to a gateway.          

1. When the gateway is initially plugged in the LED will remain red until it is fully powered up, this will take around 15 seconds.

2. Using the K3 Connect app, swipe left on the lock you would like to add, go to Info, scroll down to Gateway Management then Setup New Gateway.

3. Input your WiFi network’s name (SSID) and password when prompted. Once input select  Sync to Lock.

4. When prompted, using the pin (If lost, an unfolded paperclip will suffice) located in the gateway’s box, press the pinhole button. This will start the pairing process, a confirmation notification will be displayed on completion.

Note:  If you cannot locate the Gateway Management option, make sure both the lock’s firmware and app version is up to date.

Adding Additional Locks

        1. From the K3 Connect’s lock page swipe left on the lock in question and select Info, then Gateway Management and Use Existing Gateway.

        2. Select the Gateway you would like to add the lock to, this will start the pairing process, a confirmation will be displayed upon completion.
 

Factory Reset

1. Make sure the LED is not solid red before continuing.  See section 8 for reference.

2. Hold down the gateway’s button using the pin.  The LED will change to solid yellow, continue to hold down for 5 seconds until the LED turns off.

3. Release the button, the gateway is now set to factory settings.

LED Troubleshooting

LED Status

Scenario

Solution

No LED

Default factory settings

Gateway has not yet been setup and is still using its factory settings.

Solid red

Start up

The gateway is powering on, wait 15 seconds

Solid red

(More than 15 seconds)

Internet connection error

Check your router is functioning correctly and it has access to the internet

Solid Green

Normal operation

Gateway is paired with a lock and has an internet connection.

Solid Yellow

Button pressed

If you continue to hold the button for more than 5 seconds, the gateway will reset

Alternating red and green

Firmware update required

The gateway is updating its firmware, do not unplug the unit and wait for the LED to revert to normal

Flashing green

Setup mode

The lock is in setup mode as the button has been pressed briefly. Wait 30 seconds.

Flashing red

WiFi connection error

Make sure your router is near to the gateway and is functioning correctly. Check in the K3 Connect app that your SSID (WiFi name) and password is correct too.

Alternating off, red and green

Locks connection

Check the status of the locks.

 

Regulatory Compliance

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning Statement

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

· Reorient or relocate the receiving antenna.

· Increase the separation between the equipment and receiver.

· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

· Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimetres between the radiator and your body.



 

POI-WIFIGWY-v1:0218

 

 © 2018 Codelocks Ltd.  All rights reserved.